27 models with a 850 mm bore in this type, with outer diameter and width. Outer diameters on this page run from 1030 mm to 1220 mm.
| Model | Brand | Type | OD D (mm) | Width B (mm) | |
|---|---|---|---|---|---|
| 608/850 | ANDGE | Deep Groove Ball Bearings | 1030 | 57 | — |
| 608/850 MB | SKF | Deep Groove Ball Bearings | 1030 | 57 | — |
| 618/850 | ANDGE | Deep Groove Ball Bearings | 1030 | 82 | Cross-ref → |
| 618/850 MA | SKF | Deep Groove Ball Bearings | 1030 | 82 | — |
| 618/850-M | FAG | Deep Groove Ball Bearings | 1030 | 82 | Cross-ref → |
| 618/850F1 | ANDGE | Deep Groove Ball Bearings | 1030 | 82 | — |
| 618/850F3 | ANDGE | Deep Groove Ball Bearings | 1030 | 82 | — |
| 618/850M | ANDGE | Deep Groove Ball Bearings | 1030 | 82 | Cross-ref → |
| 618/850MA | ANDGE | Deep Groove Ball Bearings | 1030 | 82 | — |
| 618/850MA/C9 | ANDGE | Deep Groove Ball Bearings | 1030 | 82 | — |
| Series 618/850 | ANDGE | Deep Groove Ball Bearings | 1030 | 82 | — |
| Series 618/850F1 | ANDGE | Deep Groove Ball Bearings | 1030 | 82 | — |
| Series 618/850F3 | ANDGE | Deep Groove Ball Bearings | 1030 | 82 | — |
| Series 618/850M | ANDGE | Deep Groove Ball Bearings | 1030 | 82 | — |
| 619/850 | ANDGE | Deep Groove Ball Bearings | 1120 | 118 | — |
| 619/850 MA | SKF | Deep Groove Ball Bearings | 1120 | 118 | — |
| 619/850F1 | ANDGE | Deep Groove Ball Bearings | 1120 | 118 | — |
| 619/850M | ANDGE | Deep Groove Ball Bearings | 1120 | 118 | — |
| Series 619/850 | ANDGE | Deep Groove Ball Bearings | 1120 | 118 | — |
| Series 619/850M | ANDGE | Deep Groove Ball Bearings | 1120 | 118 | — |
| 1/850X3V | ANDGE | Deep Groove Ball Bearings | 1150 | 110 | — |
| 66/850V | ANDGE | Deep Groove Ball Bearings | 1150 | 110 | — |
| 306493 AA | SKF | Deep Groove Ball Bearings | 1220 | 165 | — |
| 60/850 | ANDGE | Deep Groove Ball Bearings | 1220 | 165 | — |
| 60/850 MB | SKF | Deep Groove Ball Bearings | 1220 | 165 | — |
| 60/850F1 | ANDGE | Deep Groove Ball Bearings | 1220 | 165 | — |
| Series 60/850 | ANDGE | Deep Groove Ball Bearings | 1220 | 165 | — |
The bore is the shaft diameter, so it is the one dimension you cannot change: pick the bore first, then decide the type from the load and speed, then the outer diameter from the housing you have. If the housing is fixed, filter by outer diameter in the product center. For fits and shaft tolerances see the fit recommendations.