24 models with a 69.85 mm bore in this type, with outer diameter and width. Outer diameters on this page run from 74.612 mm to 120.65 mm.
| Model | Brand | Type | OD D (mm) | Width B (mm) | |
|---|---|---|---|---|---|
| PCZ 4432 B | SKF | Spherical Plain Bearings | 74.612 | 50.8 | — |
| PCZ 4432 M | SKF | Spherical Plain Bearings | 74.612 | 50.8 | — |
| PCZ 4440 B | SKF | Spherical Plain Bearings | 74.612 | 63.5 | — |
| PCZ 4440 M | SKF | Spherical Plain Bearings | 74.612 | 63.5 | — |
| PCZ 4448 B | SKF | Spherical Plain Bearings | 74.612 | 76.2 | — |
| PCZ 4448 M | SKF | Spherical Plain Bearings | 74.612 | 76.2 | — |
| PCZ 4456 B | SKF | Spherical Plain Bearings | 74.612 | 88.9 | — |
| PCZ 4456 M | SKF | Spherical Plain Bearings | 74.612 | 88.9 | — |
| GACZ69S | ANDGE | Spherical Plain Bearings | 111.125 | 39.62 | Cross-ref → |
| GEWZ69ES | ANDGE | Spherical Plain Bearings | 111.125 | 104.775 | Cross-ref → |
| GEWZ69ES-2RS | ANDGE | Spherical Plain Bearings | 111.125 | 104.775 | Cross-ref → |
| GEZ 212 ES | SKF | Spherical Plain Bearings | 111.125 | 61.112 | — |
| GEZ 212 ES-2RS | SKF | Spherical Plain Bearings | 111.125 | 61.112 | — |
| GEZ 212 TXE-2LS | SKF | Spherical Plain Bearings | 111.125 | 61.112 | — |
| GEZ69ES | ANDGE | Spherical Plain Bearings | 111.125 | 61.112 | Cross-ref → |
| GEZ69ES-2RS | ANDGE | Spherical Plain Bearings | 111.125 | 61.112 | Cross-ref → |
| GEZ69ET-2RS | ANDGE | Spherical Plain Bearings | 111.125 | 61.112 | Cross-ref → |
| GEZM 212 ES | SKF | Spherical Plain Bearings | 111.125 | 104.775 | — |
| GEZM 212 ES-2RS | SKF | Spherical Plain Bearings | 111.125 | 104.775 | — |
| SBB 44 | IKO | Spherical Plain Bearings | 111.13 | 61.11 | — |
| SBB 44-2RS | IKO | Spherical Plain Bearings | 111.13 | 61.11 | — |
| GEGZ69ES | ANDGE | Spherical Plain Bearings | 120.65 | 70.866 | Cross-ref → |
| GEGZ69ES-2RS | ANDGE | Spherical Plain Bearings | 120.65 | 70.866 | Cross-ref → |
| GEGZ69HS/K | ANDGE | Spherical Plain Bearings | 120.65 | 70.866 | — |
The bore is the shaft diameter, so it is the one dimension you cannot change: pick the bore first, then decide the type from the load and speed, then the outer diameter from the housing you have. If the housing is fixed, filter by outer diameter in the product center. For fits and shaft tolerances see the fit recommendations.