23 models with a 536.575 mm bore in this type, with outer diameter and width. Outer diameters on this page run from 761.873 mm to 820 mm.
| Model | Brand | Type | OD D (mm) | Width B (mm) | |
|---|---|---|---|---|---|
| 306/536.575/HCP5 | ANDGE | Tapered Roller Bearings | 761.873 | 146.05 | — |
| 331682 | SKF | Tapered Roller Bearings | 761.873 | 269.875 | — |
| BT2B 332446 | SKF | Tapered Roller Bearings | 761.873 | 311.15 | — |
| BT4B 331174/HA1 | SKF | Tapered Roller Bearings | 761.873 | 558.8 | — |
| IDTB0045 | ANDGE | Tapered Roller Bearings | 761.873 | — | |
| KM276449/KM276410CD/HCRYA1 | ANDGE | Tapered Roller Bearings | 761.873 | 311.15 | — |
| M276448D/M276448D-M | ANDGE | Tapered Roller Bearings | 761.873 | — | |
| M276449/M276410 | ANDGE | Tapered Roller Bearings | 761.873 | — | |
| M276449/M276410CD | ANDGE | Tapered Roller Bearings | 761.873 | 311.15 | — |
| M276449/M276410DC | ANDGE | Tapered Roller Bearings | 761.873 | — | |
| M276449/M276449-M | ANDGE | Tapered Roller Bearings | 761.873 | — | |
| M276449ADW/M276410 | TIMKEN | Tapered Roller Bearings | 761.873 | 269.875 | — |
| M276449ADW/M276449ADW-M | ANDGE | Tapered Roller Bearings | 761.873 | — | |
| M276449D/M276410 | ANDGE | Tapered Roller Bearings | 761.873 | — | |
| M276449D/M276410/M276410D | ANDGE | Tapered Roller Bearings | 761.873 | — | |
| M276449DGW-410-410D | ANDGE | Tapered Roller Bearings | 761.873 | — | |
| M276449DW/M276410 | ANDGE | Tapered Roller Bearings | 761.873 | 269.875 | — |
| M276449DW/M276410-M276410D | ANDGE | Tapered Roller Bearings | 761.873 | 558.8 | — |
| M276449DW/M276410/HCRG2 | ANDGE | Tapered Roller Bearings | 761.873 | 269.875 | — |
| M27Series 6449/M27Series 6410 | ANDGE | Tapered Roller Bearings | 761.873 | — | |
| M27Series 6449D/M27Series 6410/M27Series 6410D | ANDGE | Tapered Roller Bearings | 761.873 | — | |
| M 276449/410 | SKF | Tapered Roller Bearings | 762 | 146.05 | — |
| BT1B 328017/HA4 | SKF | Tapered Roller Bearings | 820 | 152 | — |
The bore is the shaft diameter, so it is the one dimension you cannot change: pick the bore first, then decide the type from the load and speed, then the outer diameter from the housing you have. If the housing is fixed, filter by outer diameter in the product center. For fits and shaft tolerances see the fit recommendations.