29 models with a 47.625 mm bore in this type, with outer diameter and width. Outer diameters on this page run from 57.15 mm to 120 mm.
| Model | Brand | Type | OD D (mm) | Width B (mm) | |
|---|---|---|---|---|---|
| NAF211-34 | ANDGE | Needle Roller Bearings | — | ||
| NAF311-34 | ANDGE | Needle Roller Bearings | — | ||
| NAFC211-34 | ANDGE | Needle Roller Bearings | Cross-ref → | ||
| NAFL211-34 | ANDGE | Needle Roller Bearings | 224 | — | |
| NAFL311-34 | ANDGE | Needle Roller Bearings | 250 | — | |
| NAFS311-34 | ANDGE | Needle Roller Bearings | — | ||
| NAP311-34 | ANDGE | Needle Roller Bearings | 80 | — | |
| NAT211-34 | ANDGE | Needle Roller Bearings | 149 | — | |
| BA 3010Z | IKO | Needle Roller Bearings | 57.15 | 15.88 | — |
| BA 3012Z | IKO | Needle Roller Bearings | 57.15 | 19.05 | — |
| BA 3016Z | IKO | Needle Roller Bearings | 57.15 | 25.4 | — |
| BA 308Z | IKO | Needle Roller Bearings | 57.15 | 12.7 | — |
| BAM 3010 | IKO | Needle Roller Bearings | 57.15 | 15.88 | — |
| BAM 3012 | IKO | Needle Roller Bearings | 57.15 | 19.05 | — |
| BAM 3016 | IKO | Needle Roller Bearings | 57.15 | 25.4 | — |
| BAM 308 | IKO | Needle Roller Bearings | 57.15 | 12.7 | — |
| J-3016 | NSK | Needle Roller Bearings | 57.15 | 25.4 | — |
| MJ-30161 | NSK | Needle Roller Bearings | 57.15 | 25.4 | — |
| YB 3012 | IKO | Needle Roller Bearings | 57.15 | 19.05 | — |
| BR 303920 | IKO | Needle Roller Bearings | 61.912 | 31.75 | — |
| BR 303920 U | IKO | Needle Roller Bearings | 61.912 | 31.75 | — |
| BR 303920 UU | IKO | Needle Roller Bearings | 61.912 | 31.8 | — |
| GBR 303920 | IKO | Needle Roller Bearings | 61.912 | 31.75 | — |
| GBR 303920 U | IKO | Needle Roller Bearings | 61.912 | 31.75 | — |
| GBR 303920 UU | IKO | Needle Roller Bearings | 61.912 | 31.8 | — |
| HJ-303920 | NSK | Needle Roller Bearings | 61.912 | 31.75 | — |
| HJ-303920 + IR-253020 | NSK | Needle Roller Bearings | 61.912 | 31.75 | — |
| HC211-34 | ANDGE | Needle Roller Bearings | 100 | 25 | Cross-ref → |
| NA311-34 | ANDGE | Needle Roller Bearings | 120 | 55.6 | — |
The bore is the shaft diameter, so it is the one dimension you cannot change: pick the bore first, then decide the type from the load and speed, then the outer diameter from the housing you have. If the housing is fixed, filter by outer diameter in the product center. For fits and shaft tolerances see the fit recommendations.