24 models with a 38.1 mm bore in this type, with outer diameter and width. Outer diameters on this page run from 42.069 mm to 71.438 mm.
| Model | Brand | Type | OD D (mm) | Width B (mm) | |
|---|---|---|---|---|---|
| KF24-1 | ANDGE | Spherical Plain Bearings | — | ||
| PCZ 2416 B | SKF | Spherical Plain Bearings | 42.069 | 25.4 | — |
| PCZ 2416 M | SKF | Spherical Plain Bearings | 42.069 | 25.4 | — |
| PCZ 2420 B | SKF | Spherical Plain Bearings | 42.069 | 31.75 | — |
| PCZ 2420 M | SKF | Spherical Plain Bearings | 42.069 | 31.75 | — |
| PCZ 2424 B | SKF | Spherical Plain Bearings | 42.069 | 38.1 | — |
| PCZ 2424 M | SKF | Spherical Plain Bearings | 42.069 | 38.1 | — |
| PCZ 2432 B | SKF | Spherical Plain Bearings | 42.069 | 50.8 | — |
| PCZ 2432 M | SKF | Spherical Plain Bearings | 42.069 | 50.8 | — |
| SBB 24 | IKO | Spherical Plain Bearings | 61.91 | 33.32 | — |
| SBB 24-2RS | IKO | Spherical Plain Bearings | 61.91 | 33.32 | — |
| GACZ38S | ANDGE | Spherical Plain Bearings | 61.912 | 21.34 | Cross-ref → |
| GEWZ38ES | ANDGE | Spherical Plain Bearings | 61.913 | 57.15 | Cross-ref → |
| GEWZ38ES-2RS | ANDGE | Spherical Plain Bearings | 61.913 | 57.15 | Cross-ref → |
| GEZ 108 ES | SKF | Spherical Plain Bearings | 61.913 | 33.325 | — |
| GEZ 108 ES-2RS | SKF | Spherical Plain Bearings | 61.913 | 33.325 | — |
| GEZ 108 TXE-2LS | SKF | Spherical Plain Bearings | 61.913 | 33.325 | — |
| GEZ38ES | ANDGE | Spherical Plain Bearings | 61.913 | 33.325 | Cross-ref → |
| GEZ38ES-2RS | ANDGE | Spherical Plain Bearings | 61.913 | 33.325 | Cross-ref → |
| GEZ38ET-2RS | ANDGE | Spherical Plain Bearings | 61.913 | 33.325 | Cross-ref → |
| GEZM 108 ES | SKF | Spherical Plain Bearings | 61.913 | 57.15 | — |
| GEZM 108 ES-2RS | SKF | Spherical Plain Bearings | 61.913 | 57.15 | — |
| GEGZ38ES | ANDGE | Spherical Plain Bearings | 71.438 | 40.132 | Cross-ref → |
| GEGZ38ES-2RS | ANDGE | Spherical Plain Bearings | 71.438 | 40.132 | Cross-ref → |
The bore is the shaft diameter, so it is the one dimension you cannot change: pick the bore first, then decide the type from the load and speed, then the outer diameter from the housing you have. If the housing is fixed, filter by outer diameter in the product center. For fits and shaft tolerances see the fit recommendations.