27 models with a 32 mm bore in this type, with outer diameter and width. Outer diameters on this page run from 46.6 mm to 80 mm.
| Model | Brand | Type | OD D (mm) | Width B (mm) | |
|---|---|---|---|---|---|
| RNN32V-1 | ANDGE | Cylindrical Roller Bearings | 25 | — | |
| RNN32V-2 | ANDGE | Cylindrical Roller Bearings | 28 | — | |
| RNN32V-3 | ANDGE | Cylindrical Roller Bearings | 34 | — | |
| RNN32V-4 | ANDGE | Cylindrical Roller Bearings | 25 | — | |
| RNN32V-5 | ANDGE | Cylindrical Roller Bearings | 29 | — | |
| RNN 32x46.6x28V | ANDGE | Cylindrical Roller Bearings | 46.6 | 28 | — |
| GS 81106 | SKF | Cylindrical Roller Bearings | 47 | 3 | Cross-ref → |
| GS 81206 | SKF | Cylindrical Roller Bearings | 52 | 4.25 | Cross-ref → |
| RNU 205 | SKF | Cylindrical Roller Bearings | 52 | 15 | — |
| RNU205 | ANDGE | Cylindrical Roller Bearings | 52 | 15 | — |
| RNU205L1 | ANDGE | Cylindrical Roller Bearings | 52 | 15 | — |
| RNU205M | ANDGE | Cylindrical Roller Bearings | 52 | 15 | Cross-ref → |
| TRU 325230 | IKO | Cylindrical Roller Bearings | 52 | 30 | — |
| TRU 325230UU | IKO | Cylindrical Roller Bearings | 52 | 30 | — |
| GS 89306 | SKF | Cylindrical Roller Bearings | 60 | 6.25 | Cross-ref → |
| NCL 2/32X2V | ANDGE | Cylindrical Roller Bearings | 62 | 18 | — |
| NCL 6/32V | ANDGE | Cylindrical Roller Bearings | 62 | 18 | — |
| NCL 6/32V/P6 | ANDGE | Cylindrical Roller Bearings | 62 | 18 | — |
| NUP 6/32.5M | ANDGE | Cylindrical Roller Bearings | 62 | 16 | — |
| N 82/32M | ANDGE | Cylindrical Roller Bearings | 65 | 11 | — |
| N 82/32M/P5 | ANDGE | Cylindrical Roller Bearings | 65 | 11 | — |
| N 82/32M/P6 | ANDGE | Cylindrical Roller Bearings | 65 | 11 | — |
| N82/32 | ANDGE | Cylindrical Roller Bearings | 65 | 11 | — |
| N82/32M/P5 | ANDGE | Cylindrical Roller Bearings | 65 | 11 | — |
| NUP 45622 | ANDGE | Cylindrical Roller Bearings | 75 | 20 | — |
| NUP 6/32X3NM | ANDGE | Cylindrical Roller Bearings | 75 | 30 | — |
| NUTR 328029 | ANDGE | Cylindrical Roller Bearings | 80 | 29 | — |
The bore is the shaft diameter, so it is the one dimension you cannot change: pick the bore first, then decide the type from the load and speed, then the outer diameter from the housing you have. If the housing is fixed, filter by outer diameter in the product center. For fits and shaft tolerances see the fit recommendations.