28 models with a 170 mm bore in this type, with outer diameter and width. Outer diameters on this page run from 310 mm to 360 mm.
| Model | Brand | Type | OD D (mm) | Width B (mm) | |
|---|---|---|---|---|---|
| BND2234-Z-T-AF-S | FAG | Ball Bearing Units | 310 | — | |
| BND2234-Z-T-AL-S | FAG | Ball Bearing Units | 310 | — | |
| BND2234-Z-T-BF-S | FAG | Ball Bearing Units | 310 | — | |
| BND2234-Z-T-BL-S | FAG | Ball Bearing Units | 310 | — | |
| BND2234-Z-Y-AF-S | FAG | Ball Bearing Units | 310 | — | |
| BND2234-Z-Y-AL-S | FAG | Ball Bearing Units | 310 | — | |
| BND2234-Z-Y-BF-S | FAG | Ball Bearing Units | 310 | — | |
| BND2234-Z-Y-BL-S | FAG | Ball Bearing Units | 310 | — | |
| LOE234-N-AF-L | FAG | Ball Bearing Units | 310 | — | |
| LOE234-N-AL-L | FAG | Ball Bearing Units | 310 | — | |
| LOE234-N-BF-L | FAG | Ball Bearing Units | 310 | — | |
| LOE234-N-BL-L | FAG | Ball Bearing Units | 310 | — | |
| LOE538-N-AF-L | FAG | Ball Bearing Units | 340 | — | |
| LOE538-N-AL-L | FAG | Ball Bearing Units | 340 | — | |
| LOE538-N-BF-L | FAG | Ball Bearing Units | 340 | — | |
| LOE538-N-BL-L | FAG | Ball Bearing Units | 340 | — | |
| SD538-N-FZ-AF-L + 22238K | FAG | Ball Bearing Units | 340 | — | |
| SD538-N-FZ-AF-L + 222SM170-TVPA | FAG | Ball Bearing Units | 340 | — | |
| SD538-N-FZ-AL-L + 22238K | FAG | Ball Bearing Units | 340 | — | |
| SD538-N-FZ-AL-L + 222SM170-TVPA | FAG | Ball Bearing Units | 340 | — | |
| SD538-N-FZ-BF-L + 22238K | FAG | Ball Bearing Units | 340 | — | |
| SD538-N-FZ-BF-L + 222SM170-TVPA | FAG | Ball Bearing Units | 340 | — | |
| SD538-N-FZ-BL-L + 22238K | FAG | Ball Bearing Units | 340 | — | |
| SD538-N-FZ-BL-L + 222SM170-TVPA | FAG | Ball Bearing Units | 340 | — | |
| LOE334-N-AF-L | FAG | Ball Bearing Units | 360 | — | |
| LOE334-N-AL-L | FAG | Ball Bearing Units | 360 | — | |
| LOE334-N-BF-L | FAG | Ball Bearing Units | 360 | — | |
| LOE334-N-BL-L | FAG | Ball Bearing Units | 360 | — |
The bore is the shaft diameter, so it is the one dimension you cannot change: pick the bore first, then decide the type from the load and speed, then the outer diameter from the housing you have. If the housing is fixed, filter by outer diameter in the product center. For fits and shaft tolerances see the fit recommendations.