HH234049 - HH234011CD
📏 Dimensions on request
Product Photo
TIMKENCustom & Special Bearings
TIMKEN DV-167
Custom & Special Bearings · Dimensions on request
✓323,474 SKUs in the online catalogue
✓OEM & custom bearings welcome
✓Reply within 30 minutes (working days)
✓Global shipping from Wuxi, China
Wuxi Andge Bearing Co., Ltd.Professional bearing supplier · Wuxi, Jiangsu, China
⚡ Reply ≤ 30 min
The TIMKEN DV-167 is a Custom & Special Bearings, available in the dimensions listed in the specification table below. Supplied by Wuxi Andge Bearing Co., Ltd. (AndgeBearing), a bearing manufacturer and exporter based in Wuxi, Jiangsu, China — OEM and custom bearings welcome, RFQ replied within 30 minutes on working days.
Full Specifications
| Brand | TIMKEN |
|---|---|
| Category | Custom & Special Bearings |
| Type | Custom & Special Bearings |
| Dimensions (d × D × B) | Dimensions on request |
| Catalogue Ref. | skA6eFdWfp |
| Assembly Standout B | 1 15/Series 32 in |
| Diameter S-1 | 7 15/16 in |
| End Plug | EPS-25 |
| Installation Procedure | 1. Check shaft diameters to print specification. Remove any burrs or sharp edges. Be sure shaft surface is clean and dry beyond the area of seal location.2. Expand the V-ring seal over the shaft to the approximate inboard position (reference dimension "B" in the tables). Make sure the lip of the seal faces the bearing.3. Slide the seal cartridge onto the shaft until the V-ring fits into its cavity.4. Mount the bearing, sleeve, lockwasher and locknut in normal manner and adjust for internal clearance.Series 5. If both ends have seals, repeat steps 2 and 3 with the V-ring going on last with its lip facing the bearing.6. Thoroughly clean the housing base and remove any paint or burrs from the mating surfaces of the housing cap.7. Lower shaft, bearing and seals into the housing base, taking care to guide the seals into the seal grooves.Series 8. On each shaft there must be only one fixed bearing. If the bearing is to be fixed, the stabilizing ring can be inserted between the bearing outer ring and the housing shoulder on the locknut side of the bearing. All other bearings on this shaft should be centered in the housing.Series 9. The upper half of the housing or cap should be thoroughly cleaned and checked for burrs. Place it over the bearing and seals. The dowel pins will align the cap to the base.NOTE: housing caps and bases are not interchangeable.Series 10. After cap bolts are tightened, it is most important to position the V-ring seal to its proper fitted width. This is accomplished by moving the seal until it is flush with the outside face of the cavity. This provides proper compression of the lip against the cartridge face. |
| O-Ring | 2-262 |
| Order Instructions | Shaft seal may be ordered in place of the standard LER triple ring seals supplied with the pillow blocks listed. They also are available to retrofit existing installations.To order any pillow block housings with DUSTAC shaft seal on both sides, add the suffix "DV" to the number (e.g., SAF2522DV).To order pillow block housings with DUSTAC shaft seal and one end closed, add the suffix "DC" to the number (e.g., SAF22522DC).Standard sizes of DUSTAC shaft seals are shown in the table. Other sizes are available upon request. |
| Pillow Block Housing Number 500 | 544 |
| V-Ring Seal | V-200-A |
1900 VL V
📏 Dimensions on request
69790498027
📏 Dimensions on request
XAA33212 - Y33212
📏 Dimensions on request
MSE215BRHSATL
📏 Dimensions on request
LSM90BRHSNBATL
📏 Dimensions on request
399AS - 394DC
📏 Dimensions on request
68514439470
📏 Dimensions on request
68514458286
📏 Dimensions on request
68514436100
📏 Dimensions on request
HSM380BXHSRSS
📏 Dimensions on request
68514450020
📏 Dimensions on request