HYDNUT930.SEAL
📏 Dimensions on request
Product Photo
TIMKENCustom & Special Bearings
TIMKEN 69790498561
Custom & Special Bearings · Dimensions on request
0.02 lbWeight
✓323,474 SKUs in the online catalogue
✓OEM & custom bearings welcome
✓Reply within 30 minutes (working days)
✓Global shipping from Wuxi, China
Wuxi Andge Bearing Co., Ltd.Professional bearing supplier · Wuxi, Jiangsu, China
⚡ Reply ≤ 30 min
The TIMKEN 69790498561 is a Custom & Special Bearings, available in the dimensions listed in the specification table below, and a unit weight of 0.02 lb. Supplied by Wuxi Andge Bearing Co., Ltd. (AndgeBearing), a bearing manufacturer and exporter based in Wuxi, Jiangsu, China — OEM and custom bearings welcome, RFQ replied within 30 minutes on working days.
Full Specifications
| Brand | TIMKEN |
|---|---|
| Category | Custom & Special Bearings |
| Type | Custom & Special Bearings |
| Dimensions (d × D × B) | Dimensions on request |
| Weight | 0.02 lb |
| Catalogue Ref. | T578M8d1eg |
| Application | Internal Shaft Locking Device |
| Collar Material | Silver/Metallic |
| Coupling Size | SLD350 S |
| Cubic inches | 5.62534 mm³0.22147 in3 |
| Features | Versus Traditional Keyed ConnectionsNo Backlash due to fit tolerances No impact effect from reversing loads Ability to adjust axial position and angular timing No fretting corrosion due to movement at the fit interface Versus Traditional Interference FitsEasier and quicker to install Higher contact pressures can transmit greater torques Easy and quick to remove without damaging the shaft or hub - even after years of service Design BenefitsEliminate cost of machining keyways or splines Reduce the shaft stress by removing keyways or splines Eliminating keyways often allows the use of a smaller diameter shaft Can place anywhere on shaft, and allows for easy angular timing Easy removal without damaging the shaft or hub means easier maintenance for your customer |
| Hub Outside Diameter (Dimension d) | 19.00 mm0.748 in |
| Max. Transmissible Axial Force | 982.00 lbf |
| Max. Transmissible Torque | 30.60 ft·lb |
| Preload Force Required to Generate Max. Transmissible Torque (FA) | 4743.00 lb |
| Pressure on The Hub | 13053.00 psi |
| Pressure on The Shaft | 16099.00 psi |
| Recommended Distance to Clamp Device - 1 Element (Dimension N) | 0.118 in |
| Recommended Distance to Clamp Device - 2 Elements (Dimension N) | 0.157 in |
| Recommended Distance to Clamp Device - 3 Elements (Dimension N) | 0.157 in |
| Recommended Distance to Clamp Device - 4 Elements (Dimension N) | 0.197 in |
| Screw Material | Steel |
| Shaft Locking Device Outside Diameter (Dimension D) | 24.00 mm0.945 in |
| Shaft Size | Series 19 x 24 mm |
| Style | Low Torque |
| Tolerance of Hub Bore (T2) | -0 +0.0008 in |
| Tolerance of Shaft (T1) | +0 -0.0005 in |
| Total Width at Relaxed State (Dimension L) | 6.30 mm0.248 in |
| Type | Internal |
MSM100BXHSHTPS
📏 Dimensions on request
LSM150BXHSDQHTPS
📏 Dimensions on request
LSM70BRHSNQATL
📏 Dimensions on request
LSE304BRHSAFQRSS
📏 Dimensions on request
68514449705
📏 Dimensions on request
68514437368
📏 Dimensions on request
MSM360BRHSATL
📏 Dimensions on request
125X170X15-R2LS32-V
📏 Dimensions on request
MSM135BRHSHTPS
📏 Dimensions on request
LSE607BRHSAFQ
📏 Dimensions on request
LSM75BXHS
📏 Dimensions on request
68514446321
📏 Dimensions on request