55X100X12-RLS35-S
📏 Dimensions on request
Product Photo
TIMKENCustom & Special Bearings
TIMKEN 69790498537
Custom & Special Bearings · Dimensions on request
0.51 lbWeight
✓323,474 SKUs in the online catalogue
✓OEM & custom bearings welcome
✓Reply within 30 minutes (working days)
✓Global shipping from Wuxi, China
Wuxi Andge Bearing Co., Ltd.Professional bearing supplier · Wuxi, Jiangsu, China
⚡ Reply ≤ 30 min
The TIMKEN 69790498537 is a Custom & Special Bearings, available in the dimensions listed in the specification table below, and a unit weight of 0.51 lb. Supplied by Wuxi Andge Bearing Co., Ltd. (AndgeBearing), a bearing manufacturer and exporter based in Wuxi, Jiangsu, China — OEM and custom bearings welcome, RFQ replied within 30 minutes on working days.
Full Specifications
| Brand | TIMKEN |
|---|---|
| Category | Custom & Special Bearings |
| Type | Custom & Special Bearings |
| Dimensions (d × D × B) | Dimensions on request |
| Weight | 0.51 lb |
| Catalogue Ref. | rbpzub3p2n |
| Application | Internal Shaft Locking Device |
| Collar Material | Silver/Metallic |
| Coupling Size | SLD350 |
| Cubic inches | 295.90793 mm³11.Series 64992 in3 |
| Features | Versus Traditional Keyed ConnectionsNo Backlash due to fit tolerances No impact effect from reversing loads Ability to adjust axial position and angular timing No fretting corrosion due to movement at the fit interface Versus Traditional Interference FitsEasier and quicker to install Higher contact pressures can transmit greater torques Easy and quick to remove without damaging the shaft or hub - even after years of service Design BenefitsEliminate cost of machining keyways or splines Reduce the shaft stress by removing keyways or splines Eliminating keyways often allows the use of a smaller diameter shaft Can place anywhere on shaft, and allows for easy angular timing Easy removal without damaging the shaft or hub means easier maintenance for your customer |
| Hub Outside Diameter (Dimension d) | 95.00 mm3.740 in |
| Max. Transmissible Axial Force | 14021.00 lbf |
| Max. Transmissible Torque | 2185.00 ft·lb |
| Preload Force Required to Generate Max. Transmissible Torque (FA) | 71489.00 lb |
| Pressure on The Hub | 14504.00 psi |
| Pressure on The Shaft | 16099.00 psi |
| Recommended Distance to Clamp Device - 1 Element (Dimension N) | 0.197 in |
| Recommended Distance to Clamp Device - 2 Elements (Dimension N) | 0.236 in |
| Recommended Distance to Clamp Device - 3 Elements (Dimension N) | 0.276 in |
| Recommended Distance to Clamp Device - 4 Elements (Dimension N) | 0.315 in |
| Screw Material | Steel |
| Shaft Locking Device Outside Diameter (Dimension D) | 106.00 mm4.173 in |
| Shaft Size | 95 x 106 mm |
| Style | Low Torque |
| Tolerance of Hub Bore (T2) | -0 +0.0014 in |
| Tolerance of Shaft (T1) | +0 -0.0021 in |
| Total Width at Relaxed State (Dimension L) | 16.99 mm0.669 in |
| Type | Internal |
SNT 524-620 - 22224K - LO524
📏 Dimensions on request
HSM175BRHSKPS
📏 Dimensions on request
537X - 533D
📏 Dimensions on request
68514431057
📏 Dimensions on request
LSE411BRHS
📏 Dimensions on request
3MMC9313WI
📏 Dimensions on request
HYDNUT360-INCH.SEAL
📏 Dimensions on request
MSE708BRHSATL
📏 Dimensions on request
25580 - 25518
📏 Dimensions on request
SNT 520-617 - 23220K - LO520
📏 Dimensions on request
MSM270BXHFKPS
📏 Dimensions on request
LSE611BRHS
📏 Dimensions on request