TSX55-E-ADB
📏 Dimensions on request
Product Photo
TIMKENCustom & Special Bearings
TIMKEN 68514438845
Custom & Special Bearings · Dimensions on request
3.62 lbWeight
✓323,474 SKUs in the online catalogue
✓OEM & custom bearings welcome
✓Reply within 30 minutes (working days)
✓Global shipping from Wuxi, China
Wuxi Andge Bearing Co., Ltd.Professional bearing supplier · Wuxi, Jiangsu, China
⚡ Reply ≤ 30 min
The TIMKEN 68514438845 is a Custom & Special Bearings, available in the dimensions listed in the specification table below, and a unit weight of 3.62 lb. Supplied by Wuxi Andge Bearing Co., Ltd. (AndgeBearing), a bearing manufacturer and exporter based in Wuxi, Jiangsu, China — OEM and custom bearings welcome, RFQ replied within 30 minutes on working days.
Full Specifications
| Brand | TIMKEN |
|---|---|
| Category | Custom & Special Bearings |
| Type | Custom & Special Bearings |
| Dimensions (d × D × B) | Dimensions on request |
| Weight | 3.62 lb |
| Catalogue Ref. | 8HeRzc3x2y |
| Allowable Continuous Vibratory Torque | 300.00 N·m2650.00 in·lb |
| Bore Type | Element w/ Hardware |
| Color | Black |
| Coupling Size | LF50 |
| Coupling Type | Torsional |
| Cubic inches | 123.25443 in3 |
| Dimension HD | 100.00 mm3.937 in |
| Dynamic Torsional Stiffness | 19000.00 Nm/rad / 168100.00 in·lb/rad |
| Features | Wide range of standard designs and materials Application versatility Shaft to shaft or flywheel to shaft designs Designed to accommodate substantial shock loads, vibration, and misalignment Low moment of inertia Electrically insulating No lubrication, maintenance free Unique air-flow cooling design Different element stiffness values allow for torsional tuning of applications with diesel engines Economic design allows for cost effective solutions for torsional applications Proven L-LOC spline-clamping hub virtually eliminates spline shaft profile wear and "fretting" Oil, heat, and corrosion resistant elements (Hytrel®, Zytel®) When used with S-bolts, the coupling can accommodate some end float S-bolts accommodate applications requiring "blind" assembly Model 6 unique spacer designs span gaps between equipment in excess of the normal equipment separation Model 6 design available with bearings for high speeds and large amounts of equipment separation |
| Length thru Bore | 66.00 mm1.990 in |
| Material | High Temperature Rubber (HTR) |
| Max. Angular Misalignment | 3.00 o |
| Max. Bore (Dimensions ID1/ID2) - Flanged Hubs | 100.00 mm3.750 in |
| Max. Parallel Misalignment | 2.00 mm0.080 in |
| Max. Speed | 4000 rpm |
| Max. Torque | 2100.00 N·m18600.00 in·lb |
| Nominal Torque | 700.00 N·m6200.00 in·lb |
| Normal Temperature Range | -40 to 194 oF |
| Notes | For Hytrel, dynamic torsional stiffness values are non-linear with respect to torque. Value given is for 100% of nominal torque. Angular and parallel misalignment values are dependent on speed, and for rubber elements, should be adjusted according to figure 4. Hytrel® elements are only for applications where the driven component is piloted to the driver for SAE and DIN established alignments (i.e. Hydraulic pump flange-mounted to engine flywheel housing).Hytrel® elements are only for applications where the driven component is piloted to the driver for essentially perfect alignment (hydraulic pump flange-mounted to engine housing). |
| Shore Hardness | 60A |
| Static Angular Stiffness | 26.00 Nm/deg230.00 in·lb/deg |
| Static Axial Stiffness | 650.00 Nm/deg3700.00 lb/in |
| Static Radial Stiffness | 2200.00 Nm/deg12600.00 lb/in |
| Thread (Dimension T) | M16 |
| Torsional Element Specifications | There are two different rubber element materials available, High Temperature Rubber (HTR) and Neoprene (CR). Both elements are torsionally soft and are placed into compression during assembly. Rubber under compression can carry up to Series 5 times the amount of torque as non-compressed elements. The elements effectively accommodate shock, misalignment, and vibration plus minimize harmful radial and axial forces on the connected equipment. Neoprene (CR) is used in environments that are hostile to High Temperature Rubber (HTR).Available Durometer Hardness: 50, Series 60 (Shore A scale)Operating Temperature Range: HTR: -40° to 194° F CR: -40° to 175° FMaximum Angular Misalignment: Up to 3° |
| Wind-Up Angle at Max. Torque | 7.50 o |
| Wind-Up Angle at Nominal Torque | 3.00 o |
68514412476
📏 Dimensions on request
68514458046
📏 Dimensions on request
68514480070
📏 Dimensions on request
LSM105BRHSATL
📏 Dimensions on request
LSM45BRHSKPS
📏 Dimensions on request
LSE415BRHS
📏 Dimensions on request
84527105102
📏 Dimensions on request
68514412599
📏 Dimensions on request
69790498319
📏 Dimensions on request
69790498180
📏 Dimensions on request
MSE415BRHFATL
📏 Dimensions on request
HYDNUT225.SEAL
📏 Dimensions on request