Name: TIMKEN 68514438814
Brand: TIMKEN
SKU: OMPR60dVfn

TIMKEN 68514438814

Custom & Special Bearings · Dimensions on request

0.40 lbWeight

✓323,474 SKUs in the online catalogue ✓OEM & custom bearings welcome ✓Reply within 30 minutes (working days) ✓Global shipping from Wuxi, China

Wuxi Andge Bearing Co., Ltd.Professional bearing supplier · Wuxi, Jiangsu, China ⚡ Reply ≤ 30 min

The TIMKEN 68514438814 is a Custom & Special Bearings, available in the dimensions listed in the specification table below, and a unit weight of 0.40 lb. Supplied by Wuxi Andge Bearing Co., Ltd. (AndgeBearing), a bearing manufacturer and exporter based in Wuxi, Jiangsu, China — OEM and custom bearings welcome, RFQ replied within 30 minutes on working days.

Brand

TIMKEN

Category

Custom & Special Bearings

Type

Custom & Special Bearings

Dimensions (d × D × B)

Dimensions on request

Weight

0.40 lb

Catalogue Ref.

OMPR60dVfn

Allowable Continuous Vibratory Torque

20.00 N·m180.00 in·lb

Bore Type

Element w/ Hardware

Color

Black

Coupling Size

LF4

Coupling Type

Torsional

Cubic inches

14.59218 in3

Dimension HD

45.00 mm1.772 in

Dynamic Torsional Stiffness

850.00 Nm/rad / 7500.00 in·lb/rad

Features

Wide range of standard designs and materials Application versatility Shaft to shaft or flywheel to shaft designs Designed to accommodate substantial shock loads, vibration, and misalignment Low moment of inertia Electrically insulating No lubrication, maintenance free Unique air-flow cooling design Different element stiffness values allow for torsional tuning of applications with diesel engines Economic design allows for cost effective solutions for torsional applications Proven L-LOC spline-clamping hub virtually eliminates spline shaft profile wear and "fretting" Oil, heat, and corrosion resistant elements (Hytrel®, Zytel®) When used with S-bolts, the coupling can accommodate some end float S-bolts accommodate applications requiring "blind" assembly Model 6 unique spacer designs span gaps between equipment in excess of the normal equipment separation Model 6 design available with bearings for high speeds and large amounts of equipment separation

Length thru Bore

30.00 mm0.940 in

Material

High Temperature Rubber (HTR)

Max. Angular Misalignment

3.00 o

Max. Bore (Dimensions ID1/ID2) - Flanged Hubs

45.00 mm1.750 in

Max. Parallel Misalignment

1.50 mm0.060 in

Max. Speed

7000.00 rpm

Max. Torque

125.00 N·m1100.00 in·lb

Nominal Torque

50.00 N·m440.00 in·lb

Normal Temperature Range

-40 to 194 oF

Notes

For Hytrel, dynamic torsional stiffness values are non-linear with respect to torque. Value given is for 100% of nominal torque. Angular and parallel misalignment values are dependent on speed, and for rubber elements, should be adjusted according to figure 4. Hytrel® elements are only for applications where the driven component is piloted to the driver for SAE and DIN established alignments (i.e. Hydraulic pump flange-mounted to engine flywheel housing).Hytrel® elements are only for applications where the driven component is piloted to the driver for essentially perfect alignment (hydraulic pump flange-mounted to engine housing).

Shore Hardness

60A

Static Angular Stiffness

2.40 Nm/deg21.30 in·lb/deg

Static Axial Stiffness

75.00 Nm/deg430.00 lb/in

Static Radial Stiffness

500.00 Nm/deg2860.00 lb/in

Thread (Dimension T)

Torsional Element Specifications

There are two different rubber element materials available, High Temperature Rubber (HTR) and Neoprene (CR). Both elements are torsionally soft and are placed into compression during assembly. Rubber under compression can carry up to Series 5 times the amount of torque as non-compressed elements. The elements effectively accommodate shock, misalignment, and vibration plus minimize harmful radial and axial forces on the connected equipment. Neoprene (CR) is used in environments that are hostile to High Temperature Rubber (HTR).Available Durometer Hardness: 50, Series 60 (Shore A scale)Operating Temperature Range: HTR: -40° to 194° F CR: -40° to 175° FMaximum Angular Misalignment: Up to 3°

Wind-Up Angle at Max. Torque

12.00 o

Wind-Up Angle at Nominal Torque

5.00 o