LSE2100BXHSRSS
📏 Dimensions on request
Product Photo
TIMKENCustom & Special Bearings
TIMKEN 68514413898
Custom & Special Bearings · Dimensions on request
3.00 lbWeight
✓323,474 SKUs in the online catalogue
✓OEM & custom bearings welcome
✓Reply within 30 minutes (working days)
✓Global shipping from Wuxi, China
Wuxi Andge Bearing Co., Ltd.Professional bearing supplier · Wuxi, Jiangsu, China
⚡ Reply ≤ 30 min
The TIMKEN 68514413898 is a Custom & Special Bearings, available in the dimensions listed in the specification table below, and a unit weight of 3.00 lb. Supplied by Wuxi Andge Bearing Co., Ltd. (AndgeBearing), a bearing manufacturer and exporter based in Wuxi, Jiangsu, China — OEM and custom bearings welcome, RFQ replied within 30 minutes on working days.
Full Specifications
| Brand | TIMKEN |
|---|---|
| Category | Custom & Special Bearings |
| Type | Custom & Special Bearings |
| Dimensions (d × D × B) | Dimensions on request |
| Weight | 3.00 lb |
| Catalogue Ref. | EOCMcd6j5Y |
| # of Mounting Screws Required | 3 |
| # of Set Screws Required | 1 |
| Bore Size | 1 1/8 in |
| Bore Type | Finished Bore |
| Color | Gray/Metallic |
| Coupling Design | Flexible Spring Type Coupling with Exclusive Triple Wound Spring DesignThe Uniflex Coupling is an all steel, single piece coupling that solves a variety of application concerns including: high misalignment, space limitations, high temperature, and exceptionally low backlash/windup. The unique flexing center of the Uniflex consists of three opposingly wound square wire springs for forward or reverse operation. Two steel hubs are then brazed to the steel spring pack to create a durable one-piece flexible coupling. |
| Cubic inches | 50.78400 in3 |
| Dimension BC | 79.25 mm3.120 in |
| Dimension D | 90.42 mm3.560 in |
| Dimension FL | 12.70 mm0.500 in |
| Dimension HD | 55.12 mm2.170 in |
| Flange Diameter (Dimension FD) | 93.47 mm3.680 in |
| Hub Size | UFH125R |
| Hub Style | Regular |
| Keyway Size (W x D) | 1/4 x 1/8 in |
| Length thru Bore | 32.51 mm1.280 in |
| Material | Steel |
| Max. Bore (Dimensions ID1/ID2) | 32.00 mm1.25 in |
| Max. Parallel Offset | 1.12 mm0.044 in |
| Max. Recommended End Play | 1.02 mm0.040 in |
| Max. Speed | 6000 rpm |
| Max. Torque | 755 in·lb |
| Min. Bore (Dimensions ID1/ID2) | 15.88 mm0.625 in |
| Mounting Screw Thread Size | 5/16-18 |
| Notes | Total backlash is approximately 1/3 of windup at maximum torque – consult Lovejoy Engineering for more information.OAL & Dimension FL Tolerance + .12 inch.Mounting screws not supplied. |
| Operating Temperature Range | -40 to 250 oF |
| Overall Length | 95.25 mm3.75 in |
| Pin Location (Dimension SL) | 0.62 in |
| Rated HP at 100 rpm | 1.21 hp |
| Set Screw Thread Size (Dimension T) | 3/8-16 |
| Type | Flange-to-Shaft |
| Wind-Up Angle at Max. Torque | 4.5 o |
| Wind-Up Angle at Nominal Torque | 1.85 o |
68514412676
📏 Dimensions on request
LSE704BXHSKPS
📏 Dimensions on request
21063 - 21212
📏 Dimensions on request
68514427044
📏 Dimensions on request
M249749X - M249710
📏 Dimensions on request
MSE504BXHFHTPS
📏 Dimensions on request
HSM300BRHS
📏 Dimensions on request
45X85X10-R2LS32-S
📏 Dimensions on request
68514437257
📏 Dimensions on request
230/530KYMBW40IW534C3
📏 Dimensions on request
1200 VA R
📏 Dimensions on request